Pixie hats and very short walls

Standard

I’ve found a number of variations online of the Dolls House Emporium Market Cross;  doors cut into one of the walls with steps up, a double-decker one (that must weigh a lot), a number of gothic and faery ones and a mention in one of DHE’s chat pages of a fallen Market Cross that broke apart and had to be rebuilt.

Theinfill attempt

In the market area there’s been further work done towards the fixing of a central pillar using an old balsa wood chimney base I made when doing Hogepotche Hall and a piece of dowel.

Looking for more wall and roof avoidance action I’ve built the steps which turned in to a combo of half a ladder and a few ‘stone’ steps.

Working out the upper storey

I made the decision to go for light-weight materials up above.  The construction looks quite delicate at ground level and I’m not surprised that it can fall apart with all that weight up above.  Besides which, the ring of walls is more or less put on as a ‘oner’ which would mean more weight and a longer stretch than I could manage and it would be a good idea if a repeat of the sandwich incident could be avoided.

The roof

There’s something about the steep angle to the pinnacle like a castle turret roof that doesn’t sit well with me.  I’d like to go less with aspiring to the skies and more with a drum shape that sits firmly on the earth I think.

To that end I’ve been doing work on the walls and roof of the office space.

theinfill blog, theinfill dolls house blog, theinfill 1930s-50s Deco House, Hogepotche Hall – Dolls House Emporium Market Cross kit

I’ve done two or three runs through with different materials for walls and some roof sections. These remains look rather like collapsed and abandoned beach huts, don’t you think?

Some of the pieces are the same size as the kit, some have added gable bits and some have a combo of lower walling alternating with a gable or two or four, or on one build, a gable for each of the eight walls – which made it look like a fairground ride.

Am now leaning towards foam board walls for thickness so that they give a wall head for the roof slices, and grey 2 mm card for the roof.  Both walls and ceiling/roof pieces will be sandwiched with wood and card to limit warping.

Fitting the pieces

Well, this is proving more or less guess-work and not just because I’m usually so inaccurate.  There is an inconsistent variation between the sides of the octagon of between 2.5 and 3 mm, as I found to my cost when fitting the high level spacers at the top of the pillars and then the roof of the sandwich together.  These mini variations are in where the outer ledges for the walls have been routed out and also where the dowel holes have been drilled.  It’s such a small amount that doesn’t matter with the beautifully cut kit walls and roof, but it matters a lot if you’re as silly as me and cutting fresh pieces from less chunky materials. It’ll be what it will be and fudging seems to be my ‘thing’.

Two or four?

Today is the day to have a more serious play with four gables (like a cross), shorter walls all round, shorter pixie hat roof pieces too, with the addition of a half-inch overhang beyond the wall head.

Viewing the office space

I’d like to try to work towards an attempt at an opening method using two side walls and a section of a couple of roof slices as I’m interested in opening up the view of the upper room in some other way than lifting off the hat as is intended for the kit.

I’ve got nothing against house reveals from above, but in this particular case the kit has you take off the lid (the whole roof) and you miss out on a view of a room with a lovely ceiling shaping.  That I think would be a shame and I’d like to avoid it if possible.

Also I’ve added a continuation of the pillar theme to hold up the centre of the roof and provide a place for the market super to hang his satchel or fix a torch perhaps.  I’m always looking for places to knock in a few nails.

Hmm, not keen on the four pointy bits as looks to me even more pixie-fied than before; will probably go back to two gables one at each end.

It’s a good time to consider any lighting for this convoluted room.  For this I’m going to experiment with a home decoration string of battery-powered LEDs, you know, the ones you see wound round inside a glass bowl, in the hope of achieving a general lighting downwards over the white walls of the office space.

theinfill blog, theinfill dolls house blog, theinfill 1930s-50s Deco House, Hogepotche Hall – Dolls House Emporium Market Cross kit

Don’t know if I can get it to work but they were good fun to play with 🙂
If I shape the beam pieces at the base of the ceiling pieces to be flush and leave the gap that will cause at the wall it might leave enough space to slide some of the string of lights behind, perhaps.

How ever messy the room shape and roof may look it would be sad lose a view of the beams that will be added, don’t you think?

2 responses »

Leave a Comment

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.